E+G Machine parts E+G Machine Elements E+G GN 581 lifting eye bolt Elesa+Ganter GN 581 Lifting eye bolt (rotating)Material: High-tensile forged tempered steel with pink plastic surface coating, 100% electro-magnetic tensile tested to EN 1677.Executions:- Type B: with spanner.- Type A: without spanner.Bolt: Steel, class 10.9 (tensile strength 1000 N/mm2), 100% electro magnetic tensile tested.Eye Bolt comes with RFID Chip (Radio Frequency IDentification) which contains all data and certificates. If certificates are desired separately, they can be ordered as a req .... E+G GN 581.5 lifting eye bolt st.steel Elesa+Ganter GN 581.5 Lifting eye bolt (rotating)Material: Body/Bolt in forged AISI 318 LN stainless steel with blank surface, 100% electro-magnetic tensile tested to EN 1677.Eye bolt comes with RFID Chip (Radio Frequency IDentification) which contains all data and certificates. If certificates are desired separately, they can be ordered as a request. E+G GN 583 lifting eye nut Elesa+Ganter GN 583 Lifting eye nutBody High-tensile forged tempered steel with pink plastic surface coating, 100% electro-magnetic tensile tested to EN 1677. Nut Steel, class 10.9 (tensile strength 1000 N/mm²).Lifting eye nuts GN 583 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as potentially possible in lifting eye nuts DIN 582).Lifting eye nuts GN 583 offer a high load carrying capacity and th .... E+G GN 584 Shackle Elesa+Ganter GN 584 ShackleRing bracket: Heat-treatable steel, die-forged. Hot-dip galvanised. Bolt: Heat-treatable steel, die-forged. Galvanic zinc-plated, lacquered.Standard versions - Type A: with stud bolt. - Type B: bolt with nut and split pin. E+G GN 585 Shackle Elesa+Ganter GN 585 ShackleRing bracket: Heat-treatable steel, die-forged. Hot-dip galvanised. Bolt: Heat-treatable steel, die-forged. Galvanic zinc-plated, lacquered.Standard versions – Type A: with stud bolt. – Type B: bolt with nut and split pin. E+G GN 587.1 load ring E+G GN 587.1 load rings for welding are designed for rapid mounting.Load rings GN 587.1 for welding are designed for rapid mounting. They provide high dynamic and static strength and can be loadfrom any direction with approved safety (safety factor 4) for all loading directions. The spring steel tape (Type F) holds the ring in anyposition and dampens any noise caused by vibrations. All parts are undetachably connected.The two support lugs improve the bearing of hooks and enhance the support effe .... E+G GN 1130 Lifting pin Elesa+Ganter GN 1130 Lifting pinStud, shackle: Heat-treated steel, manganese phosphated. Push button: Aluminium, red anodized. Spring: Stainless Steel.Lifting pins GN 1130 are carrier elements designed for fast and easy use. Pressing the red aluminium button will release the locking effect of the locking ball, allowing the load bolt to be moved in or out of the holding bore hole. The shackle rotates by at least 180°, with a safety flange fitted as a safeguard against inadvertent operation. Depe .... E+G GN 1130-NI Lifting pin st. steel Elesa+Ganter GN 1130-NI Lifting pinStud: AISI 630 Stainless Steel, age hardened. Shackle: AISI 316Ti Stainless Steel. Push button: Aluminium, red anodized. Spring: Stainless Steel. Special executions on request - other diameter d1. - other lengths l1. Features and applications Lifting pins GN 1130 are carrier elements designed for fast and easy use. Pressing the red aluminium button will release the locking effect of the locking ball, allowing the load bolt to be moved in or out of the holding b .... E+G GN 5860 Load ring Elesa+Ganter GN 5860 Load ringChain ring/Eye ring: High-tensile forged tempered steel, German Material No. 1.6540 with pink plastic surface coating, 100% electro-magnetic tensile tested to EN 1677. Bearing case: High-tensile forged tempered steel, German Material No. 1.6540 zinc-plated, blue passivated, 100% electro-magnetic tensile tested. Screw: Steel, Tensile strength class 10.9 (1000 N/mm²), finish Delta Tone. E+G GN 589 Lifting point Elesa+Ganter GN 589 Lifting pointMaterial: High-tensile forged tempered steel 1.6541, 100% electro-magnetic tensile tested to EN 1677, phosphated. E+G DIN 444 eye screw Elesa+Ganter DIN 444 Eye screwSpecification: Black-oxide steel, class 5.8 (tensile strength 500 N/mm²). E+G DIN 444 eye screw st. steel Elesa+Ganter DIN 444-NI Eye screwSpecification: Stainless Steel AISI 303 E+G GN 1524 Eyebolt Elesa+Ganter GN 1524 Eye screw with long treadSpecification - Tensile strength class 5.8 E+G GN 1524 eye screw st. steel Elesa+Ganter GN 1524 Eye screw with long treadSpecification: Stainless Steel NI AISI 303 E+G GN 933.5 head grub screw Elesa+Ganter GN 933.5 Hexagonal head grub screwHexagon head screw: AISI 304 stainless steel (A2).Standard versions available- Version MS: brass pivot.- Version KU: plastic privot (Polyacetal POM).- Version ZK: spherical pivot. E+G GN 444.2 eye nut Elesa+Ganter GN 444.2 Eye nutMaterial: Black-oxide steel, class 5.8 (tensile strength 500 N/mm²). E+G DIN 582/NI lifting eye bolt Elesa+Ganter DIN 582/DIN 582-NI lifting eye bolt with female threadMaterial- DIN 582 ST: Forged steel annealed body, zinc-plated blue passivated, machined contact face.- Version NI: Drop-forged stainless steel A2, machined contact face.- Version A4: Drop-forged stainless steel A4, machined contact face. E+G DIN 580/NI lifting eye bolt Elesa+Ganter DIN 580/DIN 580-NI lifting eye boltMaterial- Version ST: Forged steel annealed body, zinc-plated blue passivated, machined contact face.- Version NI: Drop-forged stainless steel A2, machined contact face.- Version A4: Drop-forged stainless steel A4, machined contact face. E+G GN 709.3 clamping pad Elesa+Ganter GN 709.1 Clamping padMaterial: Case tempered phosphate-treated steel.Ball: Blank hardened steel.Hexagon nut: Black-oxide steel according to ISO 4035 (DIN 439).Standard versions available:- Version B: smooth contact face.- Version R: serrated contact face. E+G GN 709.1 clamping pad Elesa+Ganter GN 709.1 Clamping padMaterial: Case tempered phosphate-treated steel.Ball: Blank hardened steel.Standard versions available- Version B: smooth contact face.- Version R: serrated contact face. E+G GN 709.2 clamping pad Elesa+Ganter GN 709.2 Clamping padMaterial: Case tempered phosphate-treated steel.Ball: Blank hardened steel.Standard versions available- Version B: smooth contact face.- Version R: serrated contact face. E+G GN 965 Profile systems screw Elesa+Ganter GN 965 Assembly sets for profile systems 30/40 with T-Nuts GN 506Material: Zinc-plated Steel, blue passivated.Ball: Stainless Steel.Spring: Stainless Steel.Standard versions- Type A: with cylinder head screw DIN 912, zinc plated, blue passivated.- Type B: with countersunk screw DIN 7991, zinc plated, blue passivated.- Type C: with lens screw ISO 7380, zinc plated, blue passivated.- Type D: with cylinder head screw DIN 7984, zinc plated, blue passivated. E+G GN 968 Profile systems screw Elesa+Ganter GN 968 Assembly sets for profile systems 30/40/45 with T-nuts GN 505Material: Zinc plated Steel, blue passivated. GN 505 with increased torque (Type MB). Ball/Spring: Stainless Steel.Standard versions - Type A: with cylinder head screw DIN 912, zinc plated, blue passivated. - Type B: with countersunk screw DIN 7991, zinc plated, blue passivated. - Type C: with lens screw ISO 7380, zinc plated, blue passivated. - Type D: with cylinder head screw DIN 7984, zinc plated, blue passivated .... E+G GN 505.4 dowel for T-slot Elesa+Ganter GN 505.4 Quick-insert dowels for T-slotsMaterial: Steel zinc, plated, blue passivated. E+G GN 505.5 dowel for T-slot Elesa+Ganter GN 505.5 Quick-insert dowel for T-slotsMaterial: AISI 304 stainless steel. E+G DIN 787 T-slot bolt Elesa+Ganter DIN 787 T-slot boltMaterial: Blank steel, class 8 (tensile strength 800 N/mm²). E+G GN 230 T-nut Elesa+Ganter GN 230 Shallow T-nutMaterial: Ground and hardened black-oxide steel body. E+G GN 505 dowel T-slot Elesa+Ganter GN 505 Quick-insert dowel for T-slotVersions:- Execution MB: zinc-plated steel, with increased torque.- Execution OB: zinc-plated steel, without increased torque. E+G GN 506 dowel T-slot Elesa+Ganter GN 506 T-nut with guide stepMaterial: Zinc-plated steel.Ball/Spring: Stainless steel. E+G CMC Torque amplifier collar Elese+ganter CMC Torque amplifier collarBearing case materialGlass-fibre reinforced polyamide based (PA) technopolymer, black colour, matte finish.Standard executions- CMC: AISI 52100 steel axial bearing, zinc-plated steel washers.- CMC-SST:AISI 440 C stainless steel axial bearing, AISI 303 stainless steel washers.Features and applicationsUsed in combination with clamping levers ERX., ERW., MRX., ERF., clamping knobs type VCT.SOFT or handles type L.652, CMC torque amplifier collars double the cl .... E+G GN 506.1 dowel T-slot Elesa+Ganter GN 506.1 Dowel for T-slot with no-slip deviceMaterial: Zinc-plated steel.Ball/Spring: Stainless steel. E+G GN 506.2 Dowel for T-slot Elesa+Ganter GN 506.2 Dowel for T-slot with guide and no-slip deviceMaterial: Zinc-plated steel. Spring washer: AISI 301 stainless steel, spot-welded. E+G GN 507 dowel T-slot Elesa+Ganter GN 507 Dowel for T-slotMaterial: Zinc-plated steel. E+G DIN 508 T-nut Elesa+Ganter DIN 508 T-nutMaterial - Version 8: blank steel, class 8 (tensile strength 800 N/mm²). - Version 10: black-oxide steel, class 10 (tensile strength 1000 N/mm²). E+G DIN 508 T-nut st. steel Elesa+Ganter DIN 508-NI T-nut in st. steelMaterial: AISI 303 stainless steel. E+G GN 508.1 T-nut rhombus Elesa+Ganter GN 508.1 Rhombus T-nutMaterial: Black-oxide steel, class 10 (tensile strength 1000 N/mm2). E+G GN 508.2 T-nut Elesa+Ganter GN 508.2 T-nutMaterial- Execution 8: zinc plated hardened steel, class 8 (tensile strength 800 N/mm2).- Execution 10: black oxide hardened steel, class 10 (tensile strength 1000 N/mm2). E+G DIN 6379 stud Elesa+Ganter DIN 6379 Stud for T-nutSpecificationM6 ... M12: Tensile strength class 10.9 (1000 N/mm²)M14 ... M24: Tensile strength class 8.8 (800 N/mm²) blackened E+G GN 9190.2 Side Clamps Elesa+Ganter GN 9190.2 Side Clamps with Clamping Thread and Support.With side clamps GN 9190.2, workpieces are clamped with a pivoted clamping jaw. The clamping force acts laterally and from above to pull down on the workpiece and clamp it against fixed stops and the supporting surface.Types- Type E: With serrated clamping jaw- Type P: With prism clamping jawCoding- Type G: Clamping stroke with ball point screw- Type K: Clamping stroke with adjustable hand leverMaterials- Steel, see datasheet be .... E+G GN 3490 Threaded flange Elesa+Ganter GN 3490 Threaded flangeSpecification: Steel fine casting - zinc plated, blue passivated ZB - zinc plated and plastic coated black, RAL 9005, textured finish SW E+G GN 347 nut Elesa+Ganter GN 347 Hexagon nut with levelling baseBase: Black-oxide steel.Nut: Black-oxide steel. E+G DIN 6330 nut Elesa+Ganter DIN 6330 Hexagon nutMaterial: Black-oxide steel class 10 (tensile strength 1000 N/mm2). E+G DIN 6330 nut st. steel Elesa+Ganter DIN 6330-NI stainless steel hexagon nutsMaterial: AISI 303 stainless steel E+G DIN 6331 collar nut Elesa+Ganter DIN 6331 Collar nutMaterial: Black-oxide steel class 10 (tensile strength 1000 N/mm2). E+G GN 806 protective cap Elesa+Ganter GN 806 Protective capBody: Black elastomer, hardness 85 ±5 Shore A.Threaded insert: Zinc-plated steel (type B from D=12 to 26 mm). E+G DIN 1804 slotted locknut Elesa+Ganter Slotted locknut DIN 1804Executions- H: Hardened and mating surface- W: Not hardened, not ground E+G DIN 1804-NI locknut Elesa+Ganter DIN 1804-NI Slotted locknut Material: AISI 303 Stainless steel WNI, not hardened, not grounded. E+G DIN 1810 C-Spanner Elesa+Ganter DIN 1810 C-Spanner E+G GN 184 washer Elesa+Ganter GN 184 Washer for countersunk head screwMaterial: Turned and black-oxide steel. E+G GN 184.5 washer Elesa+Ganter GN 184.5 Washer for countersunk head screwsMaterial: AISI 303 stainless steel, sandblasted matte finish. E+G GN 185 washer Elesa+Ganter GN 185 Washer for countersunk head screwMaterial: AISI 303 stainless steel, shot-blasted matte finish.Plastic disc: Polyamide based (PA) technopolymer, white colour. E+G DIN 6319 washer Elesa+Ganter DIN 6319 Concave / convex washerMaterial: Hardened and tempered steel E+G DIN 6319 washer st. steel Elesa+Ganter DIN 6319 Concave / convex washerMaterial: AISI 303 stainless steel. E+G DIN 6319-A4 Spherical washer Elesa+Ganter DIN 6319-A4 Spherical washer in stainless steelMaterial: AISI 316 stainless steel, not hardened.Standard versions- Type C: male.- Type D: female d4 = d3. E+G GN 6319.1 Spherical washer Elesa+Ganter GN 6319.1 Levelling washerMaterial: Case-hardened steel ST (hardening depth 0.2 - 0.4 mm), hardness (550 + 100) HV 10.Spherical washers combinations GN 6319.1 provide an "undetachable" connection for male and female spherical washers GN 6319. They simply storage and allow fast and efficient installation. E+G GN 6339 washer heavy duty Elesa+Ganter GN 6339 Washer for heavy duty applicationsMaterial - Version BT: case hardened black oxide steel, material-no. 1.7227, fine machined and fine ground, tensile strength Rm = 1220 - 1400 N/mm2. - Version GO: case hardened steel treated GEOMET 500, material-no. 1.7227, fine machined and fine ground, tensile strength Rm = 1220 - 1400 N/mm2. E+G DIN 6340 washer Elesa+Ganter DIN 6340 WasherMaterial: Black-oxide (not deburred) quenched and tempered steel. Hardness (350 + 80) HV 30. E+G GN 6341 washer Elesa+Ganter GN 6341 WasherMaterial: Steel ST, turned.Finish - Type BT: black-oxide. - Type ZB: zinc-plated, blue passivated.Standard versions - Version A: with cylindrical bore. - Version B: with bore for countersunk screw. E+G GN 6341-NI St. steel washer Elesa+Ganter GN 6341-NI Stainless steel washerMaterial: AISI 303 stainless steel NI, turned. Finish: Matte blasted, MT.Standard versions - Type A: with cylindrical bore. - Type B: with bore for countersunk screw. E+G GN 6343 Washer Elesa+Ganter GN 6343 Washer / Levelling disc Made from stainless steel AISI 304, turned, blank E+G DIN 6371 captive washer Elesa+Ganter DIN 6371 Captive C-shaped washer with flat shoulder screwMaterial: Tempered black-oxide steel body with DIN 923 flat shoulder screw in black-oxide steel. E+G GN 183 C-shaped washer Elesa+Ganter GN 183 C-shaped washerMaterial: Case-hardened and black-oxide steel.The GN 18 C disc transfers a screw or nut clamping force to the item. When the thread is loosened, the disc can be pulled out of the buckle area. E+G GN 6342 friction bearing Elesa+Ganter GN 6342 friction bearingMaterial: Steel ST, blackened. Sliding disk: Plastic Polyamide 46, glasfibre reinforced. Temperature resistant up to 120 °C. Slightly greased (PTFE-mounting grease). E+G GN 6342-NI friction bearing Elesa+Ganter GN 6342-NI friction bearing in stainless steelMaterial: AISI 303 stainless steel. Sliding disk: Plastic Polyamide 46, glasfibre reinforced. Temperature resistant up to 120 °C. Slightly greased (PTFE-mounting grease). E+G GN 338 disc Elesa+Ganter GN 338 Disc with protection capDisc: Zinc-plated steel.Cover cap- Version KS: acetal resin based (POM) technopolymer, RAL 9001 white colour. Resistant to solvents, oils, greases and otherchemical agents.- Version KR: thermoplastic elastomer (TPE), 78 Shore E+G GN 346 thrust pad Elesa+Ganter GN 346 Thrust pad with ball joint and threaded holeMaterial: Zinc-plated steel, class 5.8 (tensile strength 500 N/mm²). E+G GN 187.1 guide pot Elesa+Ganter GN 187.1/GN 187.1-NI guide potMaterial- GN 187.1: Black-oxide steel.- GN 187.1-NI: AISI 303 stainless steel. E+G GN 187.2 push spring st.steel Elesa+Ganter GN 187.2 Push spring in stainless steelMaterial: AISI 301 stainless steel. E+G GN 187.4 locking plate Elesa+Ganter GN 187.4/GN 187.4-NI Serrated locking plateMaterial- GN 187.4: Sintered Steel, hardened, black oxidised with vapor, ST- GN 187.4-NI: AISI 316 LHC Stainless Steel, NIVersion- Type A: with tapped hole d3 in the center, with two countersunk holes d5 for cap screws.- Type B: with drilling d4 in the center, with two countersunk holes d5 for cap screws.- Type C: with tapped hole d3 in the center, with two tapped mounting holes d6.- Type D: with drilling d4 in the center, with two tapped m .... E+G GN 187.5 Locking plate Elesa+Ganter GN 187.5 Stainless Steel-Locking plates.GN 187.5 can be installed in combination with locking joint sets GN 187.6 to create locking joints. This allows gear lever handles and retaining tubes or trays and mounts to be adjusted relative to each other at defined angles with a form-locking connection. The angle orientation of the teeth is adapted to the connecting elements, permitting an axis-parallel or right-angled arrangement. Held together and centered by locking joint sets, the var .... E+G GN 187.6 Locking joint set Elesa+Ganter GN 187.6 Locking joint set.Can be used to combine Stainless Steel-Locking heads GN 187.5 to form locking joints.Thanks to the hexagonal shoulder, which creates a form-locking connection that prevents the part from also turning, the centering threaded bushing allows fast and easy mounting.In the unlocked state, it forms the axis that positions the locking heads center to center.The use of Stainless Steel-Thrust springs GN 187.2 allows the locking heads to be cleanly separated from ea .... E+G GN 418.2 cam point screw Elesa+Ganter GN 418.2 cam point screwSpecifications:Steel- case hardened HRC 56 ±1- Tensile strength class 8.8 (800 N/mm2)- zinc plated, blue passivatedCam point screws GN 418.2 are sturdy and compact elements, requiring a minimum of installation space and offering ultimate convenience and ease in handling. E+G GN 605 grub screw Elesa+Ganter GN 605 Grub screws with ball terminalMaterial: Black-oxide steel, hexagon socket head.Ball: Hardened steel.- Type AN: full ball for applications requiring a single contact point.- Type BN: reversible flat-faced ball for fitting non-parallel surfaces.- Type VN: non-reversible flat-faced ball.- Type VRN: non-reversible knurled flat-faced ball.Maximum ball plane inclination for flat-faced balls = 9°. E+G GN 605 st. steel grub screw Elesa+Ganter GN 605 Grub screws with ball terminalMaterial: AISI 304 stainless steel, hexagon socket head.Ball: Hardened steel.- Type AN: full ball for applications requiring a single contact point.- Type BN: reversible flat-faced ball for fitting non-parallel surfaces.- Type VN: non-reversible flat-faced ball.- Type VRN: non-reversible knurled flat-faced ball.Maximum ball plane inclination for flat-faced balls = 9°. E+G GN 913.2 grub screw Elesa+Ganter GN 913.2 Grub screwScrew made from steel, blackened.Nose- Execution A: steel, hardened and spherical.- Execution B: steel, hardened and pointed. E+G GN 913.3/ GN 913.5 grub screw Elesa+Ganter GN 913.3 grub screw and GN 913.5 Grub screw in stainless steelGN 913.3:Material: Black-oxide steel, class 5.8 (tensile strength 500 N/mm²), hexagon socket head.Bolt:- Version KU: acetal resin based (POM) technopolymer, natural colour.- Version MS: brass.GN 913.5Material: AISI 303 stainless steel, hexagon socket head.Bolt:- Version KU: acetal resin based (POM) technopolymer, natural colour.- Version MS: brass. E+G GN 606 grub screw Elesa+Ganter GN 606 Set screws with ball terminalMaterial: Black-oxide steel, hexagon socket head.Ball: Hardened steel.- Type AN: full ball for applications requiring a single contact point.- Type BN: reversible flat-faced ball for fitting non-parallel surfaces.- Type VN: non-reversible flat-faced ball.- Type VRN: non-reversible knurled flat-faced ball.Maximum ball plane inclination for flat-faced balls = 9°. E+G GN 606 st. steel grub screw Elesa+Ganter GN 606-NI Set screws with ball terminalMaterial: AISI 304 / AISI 440C stainless steel, hexagon socket head.Ball: Hardened stainless steel.- Type AN: full ball for applications requiring a single contact point.- Type BN: reversible flat-faced ball for fitting non-parallel surfaces.- Type VN: non-reversible flat-faced ball.- Type VRN: non-reversible knurled flat-faced ball.Maximum ball plane inclination for flat-faced balls = 9°. E+G GN 732.1 shoulder screw Elesa+Ganter GN 732 Shoulder screw with collarMaterial: Class 5.8 steel, hardened all round (hardening depth 0.2 - 0.4 mm). Tensile strength 500 N/mm2.Stainless Steel NIAISI 303 E+G GN 1132 Bush for lifting pin Elesa+Ganter GN 1132 Bushes for lifting pinBush: AISI 630 Stainless Steel, precipitation hardened.Type A: with external hexagon. Special executions on request other lengths (l1, l2, l3) and other threads (d3)Holding bushes GN 1132 are used in connection with lifting pins GN 1130. The length l1 of the holding bush should be equal to length l1 of the lifting pin in order to reach the load specification given in the table for GN 1130 at plug-in length x.Holding bushes are intended to remain permane .... E+G GN 912.2 Cap screw Elesa+Ganter GN 912.2 captive socket cap screw.Captive socket cap screws GN 912.2 can be used to prevent loss of the thumb screw, due to the d3 recessed portion of the stud which is shown in the datasheet.Depending on the design and required clamping length (a1-a3) of the component being attached, there are a number of assembly options shown in the datasheet.Material: Stainless Steel AISI 304 (A2) E+G ISO 7379 Shoulder screw Elesa+Ganter ISO 7379 Shoulder screw with collarMaterial: Black-oxide steel class 12.9 (tensile strength 1200 N/mm2) Adapter dimension d1 ground. E+G DIN 6320 Foot Elesa+Ganter DIN 6320 FootMaterial: Black-oxide steel, not hardened. E+G GN 409.1 Positioning element Elesa+Ganter GN 409.1 Positioning elementMaterial: Black-oxide, hardened steel.Standard versions - Type B: smooth contact face. - Type K: spherical contact face. - Type R: serrated contact face. E+G GN 409.2 Positioning element Elesa+Ganter GN 409.2 Positioning elementMaterial: Black-oxide, hardened steel.Standard versions - Type B: smooth contact face. - Type K: sphercial contact face. - Type R: serrated contact face. E+G GN 771.1 guide pin Elesa+Ganter GN 771.1 Guide pinMaterial: Hardened steel (HRC 60 ± 2), fit sizes ground.Guide pins GN 771.1 are normally used in combination with DIN 172 / DIN 179 guide bushes. The shaft tolerance p6 guarantees a perfect pressfit in a mounting borehole H7; the attachment lug l3 makes the installation easier. E+G DIN 6321 Positioning element Elesa+Ganter DIN 6321 Positioning elementMaterial Black-oxide, hardened steel.Standard versions - Type A: Headed dowel, low, without centre hole. - Type B: Workholding bolt, high, cylindrical, with centre hole. - Type C: Workholding bolt, high, flattened, with centre hole. E+G GN 6321.1 Headed dowel Elesa+Ganter GN 6321.1 Headed dowelMaterial: Hardened steel. E+G GN 6322 Positioning element Elesa+Ganter GN 6322 Machine and positioning elementMaterial: Hardened steel.Standard versions - Type B: Workholding bolt cylindrical. - Type C: Workholding bolt flattened. E+G DIN 172/DIN 179 guide bushing Elesa+Ganter DIN 172 and DIN 179 Guide bushing.Material: Ground and hardened steel (HRC 60 ± 2).For applications involving positioning, we recommend the combination with the GN 771.1 guide pins. E+G GN 411.2 bore clamp Elesa+Ganter centring bore clamps GN 411.2Versions- Type K: With clamping balls- Type S: With clamping segmentsWorkpieces can be centrally positioned and clamped from the inside of the bore.GN 411.2 offers the following advantages: - Precise self centering - Repetitive accuracy: ± 0,025 - Accuracy of concentricity: ± 0,05 - Solid and stable clamping through either 3 or 6 contact points on the workpiece - Clamping of workpieces with uneven or irregular surface (such as castings) - Distortion fr .... E+G GN 251 setting bolt Elesa+Ganter GN 251 Setting boltMaterial- Black-oxide steel bolt with hardened hexagon head (type AK).- Nickel plated steel bolt with Polyurethan disc (type BK).Locking nut: Steel zinc plated, blue passivated. E+G GN 704 Set collar Elesa+Ganter GN 704 Quick release set collarMaterial:- Ring: Aluminium, black anodised.- Lever: Aluminium, yellow anodised. E+G GN 705 positioning ring Elesa+Ganter GN 705 positioning ring for screw assembly according to DIN 705.Executions:- Version A: Grub screw with screwdriver slotted head ISO 7434 (DIN 553)- Version E: Grub screw with hexagon socket, ISO 4027 (DIN 914)Rings with d=75 and 80 mm are provided with two grub screws.Material: Black-oxide steel. E+G GN 705 st.steel positioning ring Elesa+Ganter GN 705 positioning ring for screw assembly according to DIN 705.Executions:- Version A: Grub screw with screwdriver slotted head ISO 7434 (DIN 553)- Version E: Grub screw with hexagon socket, ISO 4027 (DIN 914)Rings with d=75 and 80 mm are provided with two grub screws.Material: Stainless steel AISI 303. E+G GN 706.2 semi split set collar Elesa+Ganter GN 706.2 Semi-split set collarMaterial- Black-oxide sintered steel ST.- Aluminium ground AL. EG GN 706.3 Set collars Elesa+Ganter GN 706.3 Set collar for threaded shaftsMaterial: Black-oxide sintered steel ST. Socket head cap screw: Steel grub screw, blank, cylindrical head with hexagon socket, supplied assembled. E+G GN 706.3-NI Set collars st.steel Elesa+Ganter GN 706.3-NI Threaded set collar in stainless steelMaterial: AISI 316 LHC stainless sintered steel NI. Socket head cap screw: AISI 304 stainless steel NI. E+G GN 706.4 set collar Elesa+Ganter GN 706.4 semi split set collar with adjustable handleMaterial - Type ST: Black-oxide with vapor sintered steel - Type AL: Aluminium ground Adjustable handle - Lever body, zinc alloy die-cast, RAL 9005 black matte finish, epoxy resin coating. - with setting screw AISI 303 Stainless Steel.Semi-split set collars GN 706.4 can safely and simply be assembled i.e. with high clamping force without damaging the surface of the shaft. For size d1= 32 and 36, d3 is a through hole; starting fr .... E+G GN 706.4-NI set collar st.steel Elesa+Ganter GN 706.4-NI semi split set collar in stainless steel with adjustable handle.Material: AISI 316 L stainless sintered steel NI. Adjustable handle:- Lever body, zinc alloy die-cast, RAL 9005 black matte finish, epoxy resin coating. - with setting screw AISI 303 Stainless Steel.Can safely and simply be assembled i.e. with high clamping force without damaging the surface of the shaft. These set collars not only serve as an end stop, but they can also be used for fixing or triggering othe .... E+G GN 707.2 Split set collar Elesa+Ganter GN 707.2 split set collarMaterial ST: Black-oxide sintered steel ST. NI: Stainless steelShaft tolerance = h11.Split set collars GN 707.2 are used when the latter cannot be slipped over a shaft. These set collars not only serve as an end stop, but they can also be used for fixing or triggering other components such as end limit switches.Can be delivered in A4-stainless steel in certain sizes (see datasheet). E+G GN 826 Clamping element Elesa+Ganter GN 826 Clamping element with adjustable hand levers GN 302-30Material: Aluminium, anodized black ELS.Wedge: Adjustable hand levers GN 302-30 -Lever body, zinc alloy die-cast, RAL 9005 black matte finish, epoxy resin coating. - with setting screw AISI 303 Stainless Steel.Standard versions - Type H: Clamping screw with adjustable handle. - Type S: Clamping screw with internal hexagon. E+G GN 928/928.1 clamping element Elesa+Ganter GN 928/GN 928.1 Clamping element for round cross section shaftsMaterial: Body in black-oxide steel.Cap screw: DIN 912, zinc-plated steel.GN 928 shaft clamping units are used to clamp economically and rapidly round workpieces from 6 to 125 mm. For the application of GN 928 on large holders and away from the outside edge, spacers or special bolts are available. E+G GN 918/918.5 cam locking lever Elesa+Ganter GN 918/918.5 cam locking leverAssembly- Type KV: with ball lever, angular (serrations).- Type SK: with hexagon.- Version R: clockwise rotation (drawn version).- Version L: anti-clockwise rotation.Made from bronzed steel or stainless steel E+G GN 918.1/918.6 cam locking lever Elesa+Ganter GN 918.1/GN 918.6 Cam locking leverGN 918.1Lever: Black-oxide steel.Ball knob: DIN 319 Duroplast, shiny finish.Screw: Nitrided and black-oxide steel, hexagon socket head.Cam and washer: Case hardened and black-oxide steel.GN 918.6Lever: AISI 303 stainless steel, shot-blasted matte finish.Ball knob: DIN 319 Duroplast, shiny finish.Screw: AISI 420 stainless steel, hexagon socket head.Cam and washer: AISI 303 tempered stainless steel chemically nickel-plated.Versions:- Type KV: With ba .... E+G GN 918.2/918.7 cam locking lever Elesa+Ganter GN 918.2/GN 918.7 Cam locking leverGN 918.2Lever: Black-oxide steel.Ball knob: DIN 319 Duroplast, shiny finish.Screw: Nitrided and black-oxide steel, hexagon socket head.Cam and washer: Case hardened and black-oxide steel.GN 918.7Lever: AISI 303 stainless steel, shot-blasted matte finish.Ball knob: DIN 319 Duroplast, shiny finish.Screw: AISI 420 stainless steel, hexagon socket head.Cam and washer: AISI 303 tempered stainless steel chemically nickel-plated.Versions:- Type KV: With ba .... E+G GN 917 double cam lever Elesa+Ganter GN 917 Double cam leverMaterial: Black-oxide steel, ST52-3.King pin: Tempered AISI 420 stainless steel.Circlip: AISI 301 stainless steel.Plastic handle sleeve: Red colour, oil resistant. Max working temperature 60°C.GN 917 are used for repositioning and clamping operations. The eccentric cam is designed in such a way that the clamping force remains constant in every position of its action. It is self-locking. E+G GN 917.1 double cam lever st.steel Elesa+Ganter GN 917.1 Double cam leverMaterial: AISI 304 stainless steel, sandblasted matte finish.King pin: Tempered AISI 420 stainless steel.Circlip: AISI 301 stainless steel.Plastic handle sleeve: Red colour, oil resistant. Max working temperature 60°C.GN 917.1 is used for repositioning and clamping operations. The eccentric cam is designed in such a way that the clamping force remains constant in every position of its action. It is self-locking. E+G GN 252 blanking plug Elesa+Ganter GN 252 Blanking plugType- Type A: without micro encapsulation- Type PRB: with thread coating(polyamide allround coating)Material: Steel, tensile strength class 5.8 (500N/mm2) E+G GN 418.1 cam point lever Elesa+Ganter GN 418.1 Cam point leverMaterial: Lever in bBlack-oxide steel.Handle: Plastic ball knob DIN 319, black colour.Thread/Cam: Black oxide steel, case hardened all around, HRC 56 ±1.Standard versions available- Type R: clamping by clockwise turn (d2 = right-hand thread).- Type L: clamping by anticlockwise turn (d2 = left-hand thread).Cam point screws GN 418.2 are sturdy and compact elements, requiring a minimum of installation space and offering ultimate convenience and ease in handling .... E+G GN 919 hub with eccentric cam Elesa+Ganter GN 919 Hub with eccentric camGN 919 hubs with eccentric cam are used for adjusting and clamping operations.Material: Sintered and case-hardened black-oxide steel. E+G GN 350.3 levelling set Elesa+Ganter GN 350 / GN 350-NI Levelling setMaterial- GN 350: Zinc-plated steel ST- GN 350: AISI 303 stainless steel NI E+G GN 350.1 levelling set Elesa+Ganter GN 350.1 / GN 350.1-NI Levelling setMaterial- GN 350.1: Zinc-plated steel ST- GN 350.1-NI: AISI 303 stainless steel NI E+G GN 350.2 levelling set Elesa+Ganter GN 350.2 / GN 350.2-NI Levelling setMaterial- GN 350.2: Zinc-plated steel ST.- GN 350.2: AISI 303 stainless steel NI. E+G GN 350.3 levelling washer Elesa+Ganter GN 350.3 / GN 350.3-NI Levelling washerMateriale - GN350.3: Zinc-plated steel ST - GN350.3-NI: AISI 303 stainless steel NI E+G GN 350.5 Levelling set Elesa+Ganter GN 350.5 Levelling setLevelling sets GN 350.5 are used for levelling, adjusting and linking operations. The spherical washer allows precise installation of two non parallel planes at a required gradient up to ≈ 4°.They comprise a threaded upper sleeve and a female threaded lower sleeve. The fine thread allows a stepless and precise setting and locking using the C-Spanner DIN 1810. A locking ring serves as a height limiter for the max. height.Material: Zinc-plated steel 1.7225 (42 .... E+G GN 350.5-NI Levelling set Elesa+Ganter GN 350.5-NI Levelling setMaterial: AISI 303 (X 10 CrNiS 18-9) F1: max. total load. F2: max. load after deduction of the max. preload for screws 6.8, μ = 0.14. E+G GN 709.15 Clamping pad Elesa+Ganter GN 709.15 Clamping padMaterial: AISI 431 tempered stainless steel. Ball: AISI 420C stainless steel, nickel-plated.Standard version - B: smooth contact face. E+G GN 709.25 Clamping pad Elesa+Ganter GN 709.25 Clamping padMaterial: AISI 431 tempered stainless steel. Ball: AISI 420C stainless steel, nickel-plated.Standard version - Version B: smooth contact face. E+G GN 709.35 Clamping pad Elesa+Ganter GN 709.35 Clamping pad with long threadMaterial: AISI 431 tempered stainless steel. Ball: AISI 420C stainless steel, nickel-plated. Hexagon nut: Stainless steel according to ISO 4035 (DIN 439). E+G GN 709.6 Clamping pad Elesa+Ganter GN 709.6 Clamping padMaterial: Case tempered steel, class 10.9 Tensile strength.Ball: Hardened steel (54+2 HRC), Polyacetal (POM) plastic.O-ring: NBR synthetic rubber (Perbunan).Standard versions- Version B: Ball steel, smooth contact face.- Version R: Ball steel, serrated contact face.- Version K: Ball plastic, smooth contact face. E+G GN 709.7 Clamping pad Elesa+Ganter GN 709.7 Clamping padMaterial: Case tempered steel, class 5.8 (tensile strength 500 N/mm2). Ball: Hardened steel (54+2 HRC), Polyacetal (POM) plastic. O-ring: NBR synthetic rubber (Perbunan).Standard versions - Version B: Ball steel, smooth contact face. - Version R: Ball steel, serrated contact face. - Version K: Ball plastic, smooth contact face. E+G GN 709.8 Clamping pad Elesa+Ganter GN 709.8 Clamping padMaterial: Case tempered steel, class 5.8 (tensile strength 500 N/mm2). Ball: Hardened Steel (54+2 HRC), Polyacetal (POM) plastic. O-ring: NBR synthetic rubber (Perbunan).Standard versions - Version B: Ball steel, smooth contact face. - Version R: Ball steel, serrated contact face. - Version K: Ball plastic, smooth contact face. E+G UTB ball transfer unit Elesa+Ganter UTB ball transfer unit.UTB ball transfer units are particularly suitable for applications on transfer and conveyor lines or end of production lines. They facilitate both linear and rotational movements favouring maximum smoothness. The self-lubricating technopolymer structure ensures maximum cleanliness as it does not require lubrication with oils and greases.The technopolymer ball lends itself to handling loads with delicate surfaces. The stainless steel ball lends itself to handli .... E+G UTB-SST-ESD Elesa+Ganter UTB-SST-ESD ball transfer unit.UTB-SST-ESD ball transfer units are particularly suitable for applications on transfer and conveyor lines or end of production lines. They facilitate both linear and rotational movements favouring maximum smoothness. The special ESD conductive technopolymer prevents the accumulation of electrostatic charges. The UTB-SST-ESD ball transfer unit is therefore suitable for applications in "ESD PROTECTED AREA" (EPA) areas. The self-lubricating technopolymer .... E+G UTR roller transfer unit Elesa+Ganter UTR ball transfer unit.UTR ball transfer units are particularly suitable for applications on transfer and conveyor lines or end of production lines. They facilitate both linear and rotational movements favouring maximum smoothness. The self-lubricating technopolymer structure ensures maximum cleanliness as it does not require lubrication with oils and greases.The soft technopolymer roller is suitable for handling loads with particularly delicate surfaces such as glass and ceramic.Fu .... E+G UTR-S Ball transfer unit Elesa+Ganter UTR-S ball transfer unit.UTR ball transfer units are particularly suitable for applications on transfer and conveyor lines or end of production lines. They facilitate both linear and rotational movements favouring maximum smoothness. The self-lubricating technopolymer structure ensures maximum cleanliness as it does not require lubrication with oils and greases.The soft technopolymer roller is suitable for handling loads with particularly delicate surfaces such as glass and ceramic. .... E+G GN 509 ball transfer unit Elesa+Ganter GN 509 Ball transfer unitMaterial, housing:- Zinc-plated drawn sheet steel (version SBL, SKU and SNI).- Stainless steel (version NNI).Retaining components:Zinc-plated steel.Balls:- Version SBL: zinc-plated steel.- Version SKU: plastic.- Version SNI: stainless steel.- Version NNI: stainless steel.Retaining ringFelt seal (only for sizes D= 36 and 45).GN 509 ball transfer units are particularly suitable on conveyer tracks. They make linear or rotary movements easier even with heavy loa .... E+G GN 509.1 ball transfer unit Elesa+Ganter GN 509.1 Ball transfer unit.Material- Turned and zinc-plated steel (version SBL and SNI).- Stainless steel (version NNI).Retaining components: Zinc-plated steel.Balls: - Version SBL: steel.- Version SNI: stainless steel.- Version NNI: stainless steel.Retaining ring: Felt seal (only for sizes D= 36, 45, 62 and 100).Applications: GN 509.1 ball transfer units are particularly suitable on conveyer tracks. They make linear or rotary movements easier evenwith heavy loads (see Technical Da .... E+G GN 509.4 Ball transfer unit Elesa+Ganter GN 509.4 Ball transfer unitMaterial: Zinc-plated turned steel, blue passivated. Balls: Zinc-plated steel, blank. E+G GN 509.3 spring Elesa+Ganter GN 509.3 Spring ring for ball transfer units E+G GN 753 Guide roller Elesa+Ganter GN 753 Guide rollerVersions - Type ZL: cylindrical. - Type KV: convex. - Type KK: concave. - Type KF: wedge-shaped. - Type KR: circular (O-ring).Types - Type 1: with bore. - Type 2: with threaded stud.Outer ring: Acetal resin based (POM) technopolymer. Resistant to solvents, oils, greases and other chemical agents. Working temperature 0 °C to 40 °C. Inner ring / balls: Steel, blank. Threaded stud: Zinc plated steel. O-ring: Rubber, NBR (Perbunan), 70 Shore A E+G GN 408.1 Positioning element Elesa+Ganter GN 408.1 positioning elements with threaded stud.GN 408.1 are used in device and tool construction for mounting and positioning workpieces. They can also be used as stops, thrust pieces or feet. Type G is especially suited for applications in which the height of the supporting surfaces must be as precise as possible. On uneven or inclined surfaces, such as unmachined parts, the curved supporting surface of type K offers particular advantages.Types:Type B: Smooth contact face, turned .... E+G GN 240 quickfit coupling Elesa+Ganter GN 240 Quick-fit couplingMaterial: Steel.Version A: With male threadVersion B: With female thread E+G GN 240.1 quickfit coupling Elesa+Ganter GN 240.1 Quick-fit couplingMaterial: Steel.Version A: With male threadVersion B: With female thread E+G GN 240.2 quickfit coupling Elesa+Ganter GN 240.2 Quick-fit couplingMaterial: Coupling in Steel and spring in stainless steel. E+G GN 1050 Quick release coupling E+G GN1050 Quick release couplings position and connect components without tools using studs GN 1050.1 for a tight and repeatable fit.Types:Type A: With threaded studType I: With internal threadCoding:F: Fixed bearingL: Floating bearingMaterial:Housing in Aluminum, Black anodized ASS- Closure mechanism in Steel, tempered, Zinc plated, blue passivated- Fastening bushing (type I) in Stainless steel AISI 431, tempered- Mounting screw (type A) Socket cap screw DIN 7984, Property class 8.8- Other s .... E+G GN 1050.1 Studs Studs GN 1050.1 position and attach components without tools using quick release couplings GN 1050 for a tight and repeatable fit. The dimensions and material properties of the studs have been precisely adapted to the couplings to ensure proper functionality.Types:- Type A: With threaded stud- Type I: With internal threadMaterial:- Steel ST, tempered, Zinc plated, blue passivated E+G GN 1050.2 Flange Flanges GN 1050.2 are available as accessories for mounting quick release couplings GN 1050 and studs GN 1050.1 (see page ) to expand the attachment options of both fastening elements.CodingF: Fixed bearingL: Floating bearingMaterial- Steel ST, Zinc plated, blue passivated ZB- Countersunk screw DIN 7991, Steel, property class 8.8 Zinc plated, blue passivated E+G NSL Lead screw shafts Elesa+Ganter lead screw shafts in steel or stainless steel.Threaded shafts with single-start trapezoidal thread, right-hand tightening direction. NSL threaded shafts form, together with NSF nuts, a structured system for converting rotation into linear motion.Standard executions - NSL-A: steel.- NSL-SST: stainless steel.Special executions on request- Threaded shafts with different threads.- Threaded shafts with different lengths.- Threaded shafts in different material.- Threaded shafts with left- .... E+G NSF-W nut for lead screw E+G NSF-W nuts for E+G NSL Lead screw.NSF is used together with NSL screws form a system for converting rotation into linear motionMaterial:- Polyamide-based self-lubricating technopolymer, in beige colour.Special executions on request:- Nuts with different sizes and threads- Nuts in high temperature resistant technopolymer- Nuts with left-hand tightening direction- Nuts with multi-start threads E+G NSF-F nut for lead screw E+G NSF-F nuts for E+G NSL Lead screw. NSF is used together with NSL screws form a system for converting rotation into linear motionMaterial:Acetal resin based self-lubricating technopolymer, produced from FDA compliant raw material (FDA EU 10/2011), in white colour.Special executions on request:- Nuts with different sizes and threads- Nuts in high temperature resistant technopolymer- Nuts with left-hand tightening direction- Nuts with multi-start threads E+G GN 632.1 / GN 632.5 grub screw Elesa+Ganter GN 632.1 and GN 632.5 Grub screw with spherical endMaterial:GN 632.1 - Black-oxide steel, class 5.8 (tensile strength 500 N/mm²), hexagon socket head.GN 632.5 - AISI 303 stainless steel, hexagon socket head. E+G DIN 6332 grub screw Elesa+Ganter DIN 6332 Grub screwMaterial: Black-oxide steel, class 5.8 (tensile strength 500 N/mm²), hexagon socket head.- Execution SK: with hardened nose.- Execution SKN: with not hardened nose. E+G DIN 6311 thust pad Elesa+Ganter DIN 6311 Thrust pad with retaining ringMaterial: Turned and hardened steel.Retaining ring: Steel spring wire. E+G GN 6311.1 thrust pad Elesa+Ganter DIN 6311.1 Thrust pad with retaining ringMaterial: Black-oxide steel.VersionType A - without support.Type K - with support in acetal resin based (POM) technopolymer, natural colour.Maximum working temperature: 100°C. E+G GN 631 thrust pad Elesa+Ganter GN 631 Technopolymer thrust padMaterial: Acetal resin based (POM) technopolymer. Resistant to solvents, oils, greases and other chemical agents.Colour: Black, matte finish. E+G GN 711 ruler Elesa+Ganter GN 711 Ruler Material - Stainless steel NI, 0.6 thickness, scale etched. - Plastic KUS, highlighted in silver, 0.3 thickness, scale printed. - Plastic KUT, transparent, 0.3 thickness, scale printed. Standard versions available - Version W: figures horizontally arranged. - Version S: figures vertically arranged.With self-adhesive
