E+G Handles and knobs E+G U-handles with signal Elesa+Ganter U-handles with signal E+G GN 422 U-handle w. switch Elesa+Ganter GN 422 cabinet “U” handles come with one or two push buttons. Each button has a changeover switch and integrated LED ring lighting.When the button is pressed, an electrical control impulse to switch off a machine, for example, can be triggered based on the wiring of the contacts (NC or NO). Independent whether or not the button is actuated, the integrated LED ring lighting shines either red or green depending on the polarity of connections 1 and 2 of the LED.The cabinet „U“ .... E+G EBR-PN pneumatic Elesa+Ganter EBR-PN handle with pneumatic driveMaterial: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.Colour: Grey-black, matte finish.Push button: Light-blue technopolymer, glossy finish.Caps: Technopolymer, grey-black colour, matte finish. Supplied assembled, removable by a screwdriver.Hole: Brass bosses, threaded blind hole.EBR-PN is supplied with quick couplings for direct fitting of a tube Ø 4 mm for pneumatics.Th .... E+G EBR-SW Handle, switch Elesa+Ganter EBR-SW Handle with built-in electric switchMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourGrey-black, matte finish.Microswitch with buttonThe device is made up of a normally open contact (NO) and a normally closed contact (NC).LEDA red light and a green light indicate the microswitch status. Tension feed 24Vdc.CapsTechnopolymer, grey-black colour, matte finish. Supplied assembled, removable by a .... E+G GN 332 Handle, switch Elesa+Ganter GN 332 Tubular handles with power switching functionAluminium tube- Version SW: RAL 9005 black, matte finish, epoxy resin coating.- Version EL: anodised, natural colour, matte finish.Handle shanksZinc alloy die-cast, RAL 9005 black colour, matte finish, epoxy resin coating.Cover capsPlastic, light grey (for version without emergency stop).Types- Type T0: without button.- Type T1: with one button.- Type T2: with two buttons.Emergency stop- Identification no. 1: without emergency stop .... E+G GN 331 Handle, switch Elesa+Ganter GN 331 Tubular handles with power switching functionAluminium tube- Version SW: RAL 9005 black, matte finish, epoxy resin coating.- Version EL: anodised, natural colour, matte finish.Handle shanksZinc alloy die-cast, RAL 9005 black colour, matte finish, epoxy resin coating.Cover capsPlastic, light grey (for version without emergency stop).Types- Type T0: without button.- Type T1: with one button.- Type T2: with two buttons.Emergency stop- Identification no. 1: without emergency stop .... E+G EBR-SWB with switch Elesa+Ganter EBR-SWB Handle with bistable electronic switch.This handle is used when it is necessary for the switching to be prolonged over time. Through external logic, the Leds can be configured to indicate the specific status of the button. Example: button in neutral position green Led on, button switched on red Led off. The mechanical life of the button is 200000 cycles. In case of use of an extension with angled connector, the direction of the cable output is shown in the Fig.1. EBR-SWB han .... E+G GN 3310 Switch w/light button Elesa+Ganter GN 3310 switches with a light button come with a changeover switch and integrated LED ring light.When the button is pressed, an electrical control impulse to switch off a machine, for example, can be triggered based on the wiring of the contacts (NC or NO).Independent whether or not the button is actuated, the integrated LED ring lighting shines either red or green depending on the polarity of connections 1 and 2 of the LED.Contact type: W - Changeover contactLighting: RG:- red/gree .... E+G M.2000-SWM Bridgehandle E+G M.2000-SWM bridge handle in self-extinguishing technopolymer with monostable electrical switch.These handles are typically assembled on machine doors or protections. With the appropriate electrical connection, it is possible to configure the colour of the LED strip to indicate the status of the guard.Standard designsAll with brass bushings, M6 thread for rear mounting.8-pole cable UL: AWG22 RAL9005 PVC UL AWM 1569/2517.– M.2000-SWM-C: zinc-plated connector with 8 poles, output on the under ....
