E+G Handles and knobs E+G U-handles GN 429 U-Handle Elesa+Ganter GN 429 stainless steel cabinet u-handleStainless steel AISI 316 (A4) - Matt (Ra < 0.8 µm) MT - Polished (Ra < 0.8 µm)Sealing ring: hydrogenated acrylonitrile butadiene rubber (H-NBR), bluetemperature resistant -25 °C to +150 °CHardness 85±5 Shore AFDA compliantInformationGN 429 u-handle are intended for use in hygiene areas. The sealed mounting surface enables mounting without dead spaces; the impervious geometry in combination with thehigh quality finish prevents the acc .... E+G GN 565, GN 565.1, GN 565.5 E+G GN 565, 565.1 & 565.5 HandlesMaterialAluminium. Oval cross section bar.- Version BL: blank, tumbled.- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating. UV-resistant- Version EL: anodised, natural colour, matte finish.- Version RS: RAL 3000 red colour, epoxy resin coating.- Version SR: RAL 9006 silver colour, matte finish, epoxy resin coating.- Version WSA: RAL 9016 white colour, antimicrobial.- Version A: AISI 304 Stainless Steel, matte shot-blasted.- Version B: AISI .... E+G GN 564 Handle Elesa+Ganter GN 564 handleMaterialPolyurethane foam rubber, black colour with steel reinforcement. Soft matte finish surface highly resistant to abrasion.Temperature resistant up to 80 °C, elastic; 55±5 Shore A.AssemblyBack mounting by means of two M6 screws. E+G GN 565.2 handle Elesa+Ganter GN 565.2 handleMaterialAluminium. Oval cross section bar.- Version BL: blank, tumbled- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.- Version EL: anodised, natural colour, matte finish- Version SR: RAL 9006 silver colour, matte finish, epoxy resin coating.AssemblyTapped blind holes.Standard versions available- Type A: Mounting from the back (threaded blind bore).- Type B: Mounting from the operators side. E+G Handle M.843 Elesa+Ganter M.843 handlesMaterialHigh-resilience polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourSeven standard colours: black, orange, grey, yellow, light-blue, red, green. Glossy finish.Standard executionBrass bosses, threaded holes. E+G Handle M.843-CLEAN Elesa+Ganter M.843-CLEAN HandleMaterialHigh resilience polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourWhite similar to RAL 9002, glossy finish.Standard executionAISI 303 stainless steel bosses, threaded holes. E+G Handle M.243 Elesa+Ganter M.243 HandlesMaterialPhenolic based (PF) Duroplast. Resistant to solvents, oils, greases and other chemical agents.ColourBlack, glossy finish.AssemblyBrass bosses, tapped blind holes. E+G Handle M.643-SST-VD E+G M-643-SST-VD handle in visually detectable technopolymerElesa+Ganter M.643-SST-VD handle in visually detectable technopolymer.Glass-fibre reinforced polyamide based (PA) technopolymer, RAL 5005 blue colour, matte finish.Produced from FDA compliant raw material (FDA CFR.21 and EU 10/2011).The blue colour is easily visible in case of accidental production contamination.This makes the handle suitable for applications in the food and pharmaceutical industries.Also available in metal detectable v .... E+G U-Handle M.643-SST-MD Elesa+Ganter M.643-SST-MD handle in metal detectable technopolymer.Glass-fibre reinforced polyamide based (PA) technopolymer, RAL 5001 blue colour, matte finish.Produced from FDA compliant raw material (FDA CFR.21 and EU 10/2011).The special technopolymer contains additives detectable by means of metal detectors.Built-in zinc alloy toothed insert for coupling to the metal clamping element.The RAL 5001 blue colour is easily visible in case of accidental food contamination. Furthermore the materia .... E+G Handle M.643 Elesa+Ganter M.643 HandlesMaterialGlass-fibre reinforced polypropylene based (PP) or polyamide based (PA) technopolymer. Resistant to solvents, oils, greasesand other chemical agents.ColourBlack, matte finish.Standard execution- M.643: high-resilience polypropylene based (PP) technopolymer, brass bosses, threaded blind holes.- M.643R (reduced version h=45): polyamide based (PA) technopolymer, brass bosses, threaded blind holes. E+G Handle M.643 FM Elesa+Ganter M.643 FM Handles (Front mounting)MaterialHigh resilience polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourBlack, matte finish.AssemblyBrass bosses, through holes for cylindrical-head screws with hexagon socket. E+G Handle M.643 HT Elesa+Ganter M.643 HT handleMaterialGlass-fibre reinforced polyamide based (PA) technopolymer, resistant to high temperatures. Resistant to solvents, oils, greasesand other chemical agents.ColourBlack, matte finish.AssemblyBrass bosses, tapped blind holes.Maximum working temperature200°C. E+G GN 559 handle Elesa+Ganter GN 559 hnadleMaterialAluminium, epoxy resin coating.- Version SW: RAL 9005, black colour, matte finish.- Version SR: RAL 9006, silver, matte finish.AssemblyTapped blind holes.- Type A: closed-ended handle.- Type B: open-ended handle. E+G GN 668 handle Elesa+Ganter GN 668 HandleMaterialAluminium. Oval flat cross section bar.- Version BL: natural aluminium.- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.Assembly- Version A: back mounting, tapped blind holes.- Version B: front mounting by means of two polyamide based (PA) technopolymer adapters, black colour, matte finish and twoM5 screws. E+G GN 728, GN 728.5 handle Elesa+Ganter GN 728 & GN 728.5 handlesMaterial- Version BL: natural aluminium.- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.- Version SR: RAL 9006 silver colour, matte finish, epoxy resin coating.Stainless steel (precision casting), sand-blasted matte finish. (GN 728.5)Assembly- Type A: back mounting, tapped blind holes.- Type B: front mounting, through holes for cylindrical-head screws with hexagon socket, DIN 912. E+G GN 565.3 handle Elesa+Ganter GN 565.3 handleMaterialAluminium. Oval cross section bar.- Version BL: blank, tumbled.- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.- Version SR: RAL 9006 silver colour, matte finish, epoxy resin coating.Assembly- Version A: back mounting, tapped blind holes.- Version B: front mounting, through holes for countersunk head screws, DIN 7991. E+G GN 225 Handle Elesa+Ganter GN 225 Cabinet "U" handlesMaterialCast iron GGG.- Execution BL: blank unfinished casting, fettled.- Execution SW: RAL 9005 black colour, textured finish, epoxy resin coating. E+G Bridge handle EBP.B Elesa+Ganter EBP.B Bridge handles back mountingMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourGrey-black, matte finish.CapsTechnopolymer in Ergostyle colours, matte finish; supplied assembled, press-fit assembly, removable by a screwdriver.Available also as accessories sold separately (see caps table).Standard executionBrass bosses, threaded blind holes. E+G Handle EBP.B, EBP. SAN Elesa+Ganter EBP. Bridge handle front mounting.MaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourGrey-black, matte finish.CapsTechnopolymer in Ergostyle colours, matte finish; supplied not assembled, press-fit assembly, removable by a screwdriver.Available also as accessories sold separately (see caps table).Standard executionPass-through holes for cylindrical-head screws with hexagon socket. E+G Flexible Bridge handle EBP.FLX Elesa+Ganter EBP.FLX Flexible bridge handleMaterialPolypropylene based (PP) technopolymer elastomer-added (TPE). Resistant to solvents, oils, greases and other chemicalagents.ColourGrey-black, matte finish.CapsPolyamide based (PA) technopolymer in Ergostyle colours, matte finish. Supplied not assembled, press-fit assembly,removable by a screwdriver. Available also as accessory sold separately (see caps table).AssemblyBrass bosses with through holes for cylindrical-head screws with hexagon socket .... E+G Space sleeve DS-EBP Elesa+Ganter DS-EBP. Spacer sleeves for EBP. bridge handlesMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourGrey-black, matte finish.AssemblyThrough holes. E+G Handle M.443-CH Elesa+Ganter M.443 CH handleMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourBlack, orange, grey, red, matte finish.Standard executionsPass-through holes for cylindrical-head screws with hexagon socket.M.443/180-CH: slotted assembly holes for fitting hole centres from 149 to 152 mm. E+G Handle M.443 N-CH Elesa+Ganter M.443 N-CHMaterialGlass-fibre reinforced polypropylene based (PP) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourBlack, matte finish.Standard executionsM.443/180 N-CH: slotted assembly holes for fitting hole centres from 149 to 152 mm. E+G Handle M.443-SH Elesa+Ganter M.443 SHMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourBlack, matte finish.Standard executionPass-through holes for countersunk head screws. E+G U-handle M.443 EH Elesa+Ganter M.443 EH handlesMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourBlack, matte finish.Standard executionPass-through holes for cylindrical-head screws with hexagon socket, hexagonal-head screws or standard lock nuts. E+G Handle M.443 AE-V0 Elesa+Ganter M.443 AE-V0 handleMaterialGlass-fibre reinforced polyamide based (PA) technopolymer certified self-extinguish UL-94 V0. Resistant to solvents, oils,greases and other chemical agents.ColourBlack, matte finish.AssemblyThrough holes for cylindrical-head screws with hexagon socket. E+G U-handle M.443-ESD Elesa+Ganter M.443 ESD handleMaterialPolyamide based (PA) special antistatic technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourBlack, matte finish.AssemblyThrough holes for cylindrical head screws with hexagon socket. E+G M.543, M.543 N Handle Elesa+Ganter M.543/M543N HandlesMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourRAL 9005 black or RAL 2004 orange, matte finish.Standard executionBrass bosses, threaded blind holes. E+G GN 424.5 st. steel handle Elesa+Ganter GN 424.5 handleMaterialAISI 303 stainless steelMountingBack mounting by means of two M4 screws. E+G GN 565.4 handle Elesa+Ganter GN 565.4 Arch handleMaterialAluminium. Round cross section bar.- Version BL: blank, tumbled.- Version EL: anodised, natural colour, matte finish.- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.- Version SR: RAL 9006 silver colour, matte finish, epoxy resin coating.- Version RS: RAL 3000 red colour, matte finish, epoxy resin coating.AssemblyTapped blind holes. E+G U-handle M.478 Elesa+Ganter M.478 Bridge handleMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourBlack, glossy finish.AssemblyThrough holes for screws or rivet. E+G U-handle M.479 Elesa+Ganter M.479 Bridge handleMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourBlack, glossy finish.Screw coversTechnopolymer in six standard colours, matte finish, press-fit assembly, removable by a screwdriver.Available also as accessories sold separately (see caps table).AssemblyM.479/150-8: through holes for cylindrical-head screws with hexagon socket. Screw covers supplied not assembled.M.479/150 B-M8: .... E+G MMT. handle Elesa+Ganter MMT. handleMaterialRound cross section bar in fine ground steel with matte chrome-plated surface.Insulation componentGlass-fibre reinforced polyamide based (PA) technopolymer, black colour, matte finish. Resistant to solvents, oils, greases andother chemical agents.End bushesSteel, chrome-plated matte surface.AssemblyTapped holes. E+G GN 425.3-ST Handle Elesa+Ganter GN 425.3-ST Handle for weldingMaterialSteel ST, sandblasted matte finish.AssemblyWelding. E+G GN 425.3-NI Handle Elesa+Ganter GN 425.3-NI HandlesMaterialAISI 304 stainless steel NI.Round cross section bar without mounting holes, sandblasted matte finish.AssemblyWelding. E+G GN 427 Handle Elesa+Ganter GN 427 HandlesMaterialAluminium. Oval cross section bar.- Version EL: anodised, natural colour, matte finish.- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.- Version SR RAL 9006 silver, matte finish, epoxy resin coating.AssemblyTapped blind holes. E+G GN 425.1 handle Elesa+Ganter GN 425.1 Double-curved handleMaterialChrome-plated steel. Round cross section bar.AssemblyTapped blind holes.WashersZinc-plated steel, supplied not assembled. E+G GN 425.2 Handle Elesa+Ganter GN 425.2 Folding handleMaterialRound cross section bar, chromium-plated finish CR.AISI 303 stainless steel NI, sandblasted matte finish. (GN 425.2-NI)AssemblyBack mounting by means of two ISO 8675-M10x1 hexagon nuts and DIN 125 zinc-plated steel washers.Stop springTo keep the handle open or folded back. E+G GN 425.8 Handles Elesa+Ganter GN 425.8 Folding handle with recessed trayFolding handle- Chrome-plated steel CR.- AISI 303 stainless steel NI, matte shot-blasted.TrayDie-cast zinc alloy.- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.- Version SR: RAL 9006 silver colour, matte finish, epoxy resin coating.Standard versions available- Type A: with handle locking in the folded up or folded down position.- Type B: with spring return of the handle in the folded down position.AssemblyThrough hole .... E+G GN 730 safety handle Elesa+Ganter GN 730 Guard safety handleMaterialAluminium profile.- Version EL: anodised, natural colour, matte finish.- Version BL: natural aluminium.- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.- Version SR: RAL 9006 silver, matte finish, epoxy resin coating.AssemblyTapped blind holes. E+G Handle M.990 Elesa+Ganter M.990 Guard safety handlesMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourBlack, matte finish.Screw coverTechnopolymer in standard colours: RAL 9005 black, RAL 2004 orange, RAL 7035 grey, RAL 1021 yellow, RAL 5024 light-blue,RAL 3000 red, matte finish, snap-in assembly, removable.AssemblyThrough holes for cylindrical-head screws with hexagon socket, hexagonal-head screws or standard lock nuts. E+G ESP Guard safety handle Elesa+Ganter ESP. Guard safety handles.MaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourGrey-black, matte finish.CoverTechnopolymer in Ergostyle colours, glossy finish, supplied not assembled, snap-in assembly, removable by a screwdriver.Available also as accessory sold separately (see caps table).Assembly- Execution EH: through holes for cylindrical-head screws with hexagon socket, hexagonal-head screws or st .... E+G Guard wing handle EWP Elesa+Ganter EWP. Guard wing handlesMaterialGlass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.ColourGrey-black, matte finish.CapsTechnopolymer in Ergostyle colours, glossy finish; supplied not assembled, snap-in assembly, removable by a screwdriver.Available also as accessories sold separately (see caps table).Assembly- Execution EH: through holes for cylindrical-head screws with hexagon socket, hexagonal-head screws or stan .... E+G EPR-PF, EPR-SH, EPR/F-SH Elesa+Ganter Flush pull handle EPR-PF, EPR-SH, EPR/F-SHMounting instruction: Click on datasheet under Documents E+G Flush pull handle ERB, ERB.CLEAN Elesa+Ganter Flush pull handle ERB, ERB.CLEANMounting instruction: Click on PDF datasheet under Documents E+G GN 426 Handle Elesa+Ganter GN 426 Cabinet handlesMaterial- Aluminium bar for Ø 20 mm.- Aluminium tube, thickness 4 mm for Ø 28 mm.Colour- Version BL: natural aluminium.- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.- Version SR: RAL 9006 silver colour, matte finish, epoxy resin coating.Assembly- Tapped blind holes in the bar for Ø 20 mm.- Aluminium tapped bosses in the tube for Ø 28 mm. E+G GN 426.5 st. steel handle Elesa+Ganter GN 426.5 Cabinet handlesMaterialAISI 304 stainless steel tube, thickness 2 mm, sandblasted matte finish.AssemblyAISI 303 stainless steel bosses in the tube.- Execution A: back mounting.- Execution B: front mounting to be assembled in pairs opposed to the standard execution. E+G GN 426.1 Handle Elesa+Ganter GN 426.1 Double-curved cabinet handlesMaterial- Aluminium bar for Ø 20 mm.- Aluminium tube, thickness 4 mm for Ø 28 mm.Colour- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.- Version SR: RAL 9006 silver colour, matte finish, epoxy resin coating.- Version BL: natural aluminium.Assembly- Tapped blind holes in the bar for Ø 20 mm.- Aluminium tapped bosses in the tube for Ø 28 mm. E+G GN 333 Handle Elesa+Ganter GN 333 handleTubeAluminium, wall thickness 1.5 mm.Handle shanksDie-cast zinc alloy, RAL 9005 black colour, matte finish, epoxy resin coating, fitted to the tube by means of a screw.Tube end capsPolyamide based (PA) technopolymer.Assembly- Type A: back mounting, tapped blind holes.- Type B: front mounting, through holes for cylindrical-head screws with hexagon socket, DIN 912-M6. E+G GN 333.1handle Elesa+Ganter GN 333.1 Tubular handleMaterialAluminium, wall thickness 1.5 mm.Handle shanksDie-cast Zinc alloy, RAL 9005 black colour, matte finish, epoxy resin coating, fitted to the tube by means of a screw.Tube end capsPolyamide based (PA) technopolymer. E+G GN 333.6 Handle E+G GN 333.7 Stainless steel u-handle Elesa+Ganter GN 333.5 Tubular handlesMaterial:Tube in AISI 304 stainless steel, thickness 28x2 mm, fine grounded matte finish.Handle shanks in stainless steel (precision casting), matte sand-blasted and electropolished finish.Assembly: Tapped blind holes. E+G GN 669 Handle Elesa+Ganter GN 669 Tubular handleTube and handle shanksAluminium.- Execution EL: anodised, natural colour, matte finish, handle shanks in grey colour.- Execution SW: RAL 9005 black colour, matte finish, epoxy resin coating, handle shanks in black colour.Handle shank coversPolyamide based (PA) technopolymer, black colour, matte finish. Resistant to solvents, oils, greases and other chemicalagents.Assembly- Execution A: back mounting by means of two M8 screws, tapped blind holes.- Executoin B: fr .... E+G GN 666 and GN 666.1Handles Elesa+Ganter GN 666/GN 666.1 HandlesTubeAluminium, wall thickness 1.5 mm.Handle shanksPolyamide based (PA) technopolymer, glas fibre reinforced, temperature resistant up to 100 °C.Tube end capsPolyamide based (PA) technopolymer, glas fibre reinforced, temperature resistant up to 100 °C. E+G GN 666.5 tubular handles Elesa+Ganter GN 666.5 Tubular handlesTubeAISI 304 stainless steel, ground matte shiny finish.Handle shanksAISI 304 stainless steel, ground matte shiny finish.Grub screwAISI 304 Stainless Steel DIN 914-M5.Tube end caps- Version K: Plastic (Polyamide A), black matte finish.- Version E: AISI 304 stainless Steel. E+G GN 666.7 Tubular handles Elesa+Ganter GN 666.7 Tubular handlesTubeAISI 304 stainless steel, ground matte shiny finish.Handle shanksAISI 304 stainless steel, ground matte shiny finish.Mounting studAISI 304 stainless steel, with threaded pin DIN 913-M8.Grub screwAISI 304 Stainless Steel DIN 914-M5.Tube end caps- Version K: Plastic (Polyamide A), black matte finish.- Version E: AISI 304 stainless Steel. E+G Tubular handle M.1066 BM-CLEAN Elesa+Ganter M.1066 BN-CLEAN Tubilar handles back mountingTubeAluminium, epoxy resin coating, glossy finish. Highly resistant to wear and chemical agents. Avoid continuous contact withboiling water or steam.Handle shanksGlass-fibre reinforced polyamide based (PA) technopolymer, matte finish. Resistant to solvents, oils, greases and otherchemical agents.Tube end capsPolyamide based (PA) technopolymer.ColourWhite similar to RAL 9002.Standard executionSpecial zinc-plated steel screws with threaded .... E+G Tubular handle M.1043 Elesa+Ganter M.1043 Tubular handles front mounting.Handle shanksGlass-fibre reinforced polyamide based (PA) technopolymer, black colour, matte finish. Supplied assembled. The seat forhousing the tube in the shank is shaped so as to prevent its rotation.TubeGlass-fibre reinforced polyester, black colour with high resistivity.High resistance to wear, scratches and agents.Standard executionsPass-through holes for cylindrical-head screws with hexagon socket.Two reference pins (to be fitted during ha .... E+G Handle GN 665 Elesa+Ganter GN 665 Arch-shaped handle.MaterialAluminium. Round cross section bar.- Version SW: RAL 9005 black colour, matte finish, epoxy resin coating.- Version SR: silver, RAL 9006, matte finish, epoxy resin coating.Handle shanksZinc alloy die-cast, RAL 9006 grey colour, epoxy resin coating.AssemblyZinc-plated steel screws and washers supplied. Two reference pins, between the handle shanks and the round cross sectionbar, guarantee an exact positioning. E+G Tubular handle ETH Elesa+Ganter tubular handle ETH "Ergostyle".Black, orange, grey, yellow, light blue and red colour.Awarded with the IF Design Award 2015 for its combination of industrial design and functionality. E+G DS-ETH Spacer sleeves Elesa+Ganter DS-ETH spacer sleves for ETH.35 tubular handles.Spacer sleeves for ETH tubular handles have been designed to increase the distance between the handle and the fitting surface.Material:Glass-fibre reinforced polyamide based (PA) technopolymer, black colour or white similar to RAL 9002 (CLEAN), matte finish. E+G handles GN 481 Elesa+Ganter Edge handles GN 481MaterialAluminium profile, Ø 30 mm.End capsDie-cast zinc alloy. Fitted to the tube by means of self-tapping countersunk head screws DIN 7500-1, type M with TORX®(registered trademark of TEXTRON INC.).ColourRAL 9005 black colour, matte finish, epoxy resin coating.AssemblyThrough holes, for countersunk head screws. E+G GN 430 handles Elesa+Ganter GN 430 Guard safety handlesAluminium tube- Version SW: RAL 9005 black, matte finish, epoxy resin coating.- Version EL: anodised, natural colour, matte finish.Side end capsPolyamide based (PA) technopolymer, black grey colour. E+G GN 666.4 handles Elesa+Ganter GN 666.4 Arch-shaped handlesTubeAluminium, wall thickness 1.5 mm.Handle shanksAluminium, black, epoxy resin coating.Tube end capsPolyamide based (PA) technopolymer, glass fibre reinforced.Temperature resistant up to 100 °C.Finish- Version SW:Tube / Handle shanks: RAL 9005 black, matte finish, epoxy resin coating.Tube end caps: black, matte finish.- Version EL:Tube: anodised, natural colour.Handle shanks: RAL 9005 black colour, matte finish, epoxy resin coating.Tube end caps: black, .... E+G GN 224.1 & GN 224.5 Steel/Stainless Elesa+Ganter GN 224.1/GN 224.5 HandleMaterialSteel, Round cross section bar, chrome-plated.(GN 224.1)Stainless steel AISI 303. (GN 224.5)AssemblyTapped blind holes.WashersZinc-plated steel, supplied not assembled.(GN 224.1)Stainless steel AISI 303, supplied not assembled. (GN 224.5) E+G GN 425.5 Folding handling Elesa+Ganter GN 425.5 Folding handlesHandleChrome-plated steel. Round cross section bar.Attachment partPolyamide based (PA) technoplymer, black, matte finish.Temperature resistant up to 100 °C.CoverPolyamide based (PA) technoplymer, black-grey, matte finish.Temperature resistant up to 100 °C. E+G GN 427.5 st. steel Elesa+Ganter GN 427.5 Cabinet "U" handlesMaterialAISI 304 stainless steel, matte shot-blasted. Oval cross section bar.AssemblyTapped blind holes. E+G U-handles GN 334 Elesa+Ganter GN 334 Oval tubular handlesMaterialAluminium.Handle shanksDie-cast zinc alloy, epoxy resin coating.FinishVersion SW:- Tube: RAL 9005 black colour, matte finish, epoxy resin coating- Handle shanks: RAL 9005 black colour, matte finish, epoxy resin coatingVersion EL:- Tube: anodised, natural colour- Handle shanks: RAL 9005 black colour, matte finish, epoxy resin coatingVersion ES:- Tube: anodised, natural colour- Handle shanks: silver RAL 9006, matte finishEnd capsPolyamide based (PA) .... E+G handles GN 334.1 Elesa+Ganter GN 334.1 Oval tubular handles with inclined shanksTubeAluminium.Handle shanksDie-cast zinc alloy, epoxy resin coating.FinishVersion SW:- Tube: RAL 9005 black colour, matte finish, epoxy resin coating.- Handle shanks: RAL 9005 black colour, matte finish, epoxy resin coating.Version EL:- Tube: anodised, natural colour.- Handle shanks: RAL 9005 black colour, matte finish, epoxy resin coating.Version ES:- Tube: anodised, natural colour.- Handle shanks: silver RAL 9006, matte finish, epo .... E+G GN 335 oval tubular handle Elesa+Ganter GN 335 oval tubular handles have an inclined handle profile with a 45° angle. These handles are comfortable and ergonomic to grasp in a variety of applications such as sliding doors.Types:Type A: Mounting from the back (threaded blind bore)Type B: Mounting from the operators sideHandle tube:- AluminumHandle legs:- Zinc die castingplastic coatedTube SW: Black, RAL 9005, textured finish, plastic coatedHandle legs black, RAL 9005, textured finishTube EL: Anodized, natural colorHandle .... E+G Tubular handle M.1043-HEI Elesa+Ganter M.1043-HEI Tubular handles high electrical insulationHandle shanksGlass-fibre reinforced polyamide based (PA) technopolymer, black colour, matte finish. Supplied assembled. The seat forhousing the tube in the shank is shaped so as to prevent its rotation.TubeGlass-fibre reinforced polyester, black colour with high resistivity. High resistance to wear, scratches and agents.AssemblyRear fastening with screws M10.Two reference pins (to be fitted during assembly) guarantee a precise pos .... E+G GN 423 handles Elesa+Ganter U-handles GN 423Version ELS: Handle bar: anodised, natural colour, and handle shanks: black, matte finish. Version ESS: Handle bar: anodised, black colour, and handle shanks: black, matte finish. Version ELG: Handle bar: anodised, natural colour, and handle shanks: grey, matte finish. E+G GN 424.1 U-handle Elesa-Ganter GN 424.1 Arch-shaped handle Material: Steel. Round cross section bar. - Version SW: RAL 9005 black, matte finish, epoxy resin coating. - Version SR: RAL 9006 silver, matte finish, epoxy resin coating. - Version CR: chrome-plated surface. Assembly: Tapped blind holes. E+G M.943 U-handle Elesa-Ganter M.943 U-handle Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents. Colour: Black, matte finish. Standard executions: - M.943-B: brass bosses, threaded blind holes. - M.943-AF: blind holes for self-tapping screws Ø 4.8 (UNI ISO 7049). Maximum torque recommended 5 Nm. E+G GN 333.8 Handle shanks Elesa-Ganter GN 333.8 Handle shank Material: Zinc alloy, die-cast. - Version SW: RAL 9005, black colour, matte finish, epoxy resin coating. - Version SR: RAL 9006, silver, matte textured finish, epoxy resin coating. Assembly (Type A): back mounting by means of a M8 screw, tapped blind hole. E+G MPE Folding handle Elesa-Ganter MPE Folding handle Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents. Colour: RAL 9005 black, matte finish. Rotation pin and return springs: AISI 303 stainless steel pin, AISI 302 stainless steel springs. E+G MPR Folding handle Elesa-Ganter MPR Folding handle Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents. Colour: Black, matte finish. Rotation pin and return springs: AISI 303 stainless steel pin, AISI 302 stainless steel springs. E+G MSP Safety handles Elesa-Ganter MSP Safety handle Material: Glass-fibre reinforced polyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents. Colour: Grey-black, matte finish. Standard executions: - MSP-B: brass boss, threaded blind hole. Fitting by means of no. 2 M6 screws (maximum length same as the panel thickness + 10 mm), not included in the supply. - MSP-AF:fitting by means of no. 2 self-tapping screws for plastic materials Ø5 (UNI ISO 7049)(maximum length same as th .... E+G GN 333.9 Handle shanks Elesa-Ganter GN 333.9 Handle shank Material: Zinc alloy, die-cast. – Version SW: RAL 9005, black colour, matte finish, epoxy resin coating. – Version SR: RAL 9006, silver, matte textured finish, epoxy resin coating. Assembly (Type A): back mounting by means of a M8 screw, tapped blind hole. E+G GN 366 Handle Elesa-Ganter GN 366 Handle Tube: Aluminium, wall thickness 2 mm. Handle shanks / Tube end caps: Polyamide based (PA) technpolymer, glas fibre reinforced, temperature resistant up to 100 °C. Finish - Version SW: Tube in RAL 9005, black colour, matte finish, epoxy resin coating. Handle shanks and tube end caps in black, matte finish. - Version ELS: Tube in anodised aluminium, natural colour. Handle shanks and tube end caps in black, matte finish. - Version ELG: Tube in anodised aluminium, natural .... E+G GN 430.1 Ledge handel Elesa-Ganter GN 430.1 Ledge handel Aluminium tube - Version SW: RAL 9005 black, matte finish, epoxy resin coating. - Version EL: anodised, natural colour, matte finish. Side end caps: Polyamide based (PA) technopolymer, black grey colour E+G GN 930 Handle tubes Elesa-Ganter GN 930 Handle tube Material: Aluminium. - Version SW: RAL 9005 black colour, matte finish, epoxy resin coating (available for lengths until 3000 mm). - Version EL: anodised, natural colour, matte finish (available for lengths until 2600 mm). E+G GN 333.2 Tubular handle Elesa-Ganter GN 333.2 Tubular handle Material: Aluminium, wall thickness 1.5 mm. Handle shanks: Die-cast zinc alloy, epoxy resin coating. Finish - Version SW: Tube and Handle shanks in RAL 9005 black colour, matte finish, epoxy resin coating. Cover caps in black, matte finish. - Version ELS: Tube in anodised aluminium, natural colour. Handle shanks in RAL 9005 black colour, matte finish, epoxy resin coating. Cover caps in black, matte finish. - Version ELG: Tube in anodised aluminium, natural co .... E+G GN 333.3 Tubular handle Elesa-Ganter GN 333.3 Tubular handle Material: Aluminium, wall thickness 1.5 mm. Handle shanks: Die-cast zinc alloy, epoxy resin coating. Finish - Version SW: Tube and handle shanks in RAL 9005 black colour, matte finish, epoxy resin coating. Cover caps in black, matte finish. - Version ELS: Tube in anodised aluminium, natural colour. Handle shanks in RAL 9005 black colour, matte finish, epoxy resin coating. Cover caps in black, matte finish. - Version ELG: Tube in anodised, natural colour. Hand .... E+G GN 565.9 handle Elesa-Ganter GN 565.9 Handle Material: AISI 304 stainless steel, matt shot blasted MT. Standard versions available: - Type A: back mounting, tapped blind holes. - Type B: front mounting, through holes for cylindrical head screws with hexagon socket, DIN 912. E+G GN 425 handle Elesa+Ganter GN 425 HandleMaterialSteel. Round cross section bar.- Version CR: chrome-plated surface.- Version BT: black-oxide surface.- Version SW: RAL 9005 black, matte finish, epoxy resin coating.- Version RS: RAL 3000 red, matte finish, epoxy resin coating.AssemblyTapped blind holes.WashersZinc-plated steel, supplied not assembled. E+G GN 425-A4 handle Elesa+Ganter GN 425-A4 HandleMaterialAISI 316L stainless steel (A4).AssemblyTapped blind holes.WashersAISI 316L stainless steel, supplied not assembled. E+G GN 425-AL Handle Elesa+Ganter GN 425-AL HandleSpecificationAluminium AL- plastic coatedblack, RAL 9005 textured finish SWsilver, RAL 9006, textured finish SRred, RAL 9003, textured finish RS- anodized, natural colour ELLocation discs- Stainless Steel AISI 303 E+G GN 425-NI Handle Elesa+Ganter GN 425-Ni HandleMaterialAISI 303 stainless steel (Ø 8/10) and AISI 304 stainless steel (Ø 12/16). Round cross section bar.Finish- Version NI: sandblasted matte finish.- Version NEP: electropolished.AssemblyTapped blind holes.WashersAISI 303 stainless steel, supplied not assembled. E+G GN 565.7 Handle Elesa+Ganter GN 565.7 Inclined Stainless Steel-Cabinet "U" handleMade from stainless steel AISI 304, matt shot-blasted MTSpecification, type A: Mounting from the back (threaded blind bore) E+G GN 181 Fastening sets Elesa+Ganter GN 181 Fastening sets (set of 2 pcs.)Made from zinc die casting ZD, with plastic coating: - black, RAL 9005 textured finish SW - silver, RAL 9006 textured finish SRCountersunk screw DIN 7991 made from steel, zinc plated, blue passivated.Fastening sets GN 181 make it possible to mount different cabinet "U" handles and tubular handles with internal thread from the operator's side. The mounting position of the fastening plates is freely customizable, allowing a sideways offset or mount .... GN 426.3 cabinet “U” handle Elesa+Ganter GN 426.3 cabinet “U” handleType A: simply curved, 90° Material: Steel ST, blank, oiledGN 426.3 cabinet “U” handles are produced through bending. This allows special lengths or special geometries with the same r and s dimensions to be delivered even in comparatively small unit quantities. For welding. E+G GN 426.6 Handle Elesa+Ganter GN 426.6 Stainless Steel-Cabinet "U" handles Stainless Steel-Cabinet "U" handles Types - Type A: Mounting from the back (threaded blind bore) - Type B: Mounting from the Operators sideMaterial: Stainless Steel AISI 304, matt shot-blasted Threaded bush / Mounting stud Stainless Steel AISI 303 Grub screw DIN-914-M5-6-NI E+G GN 428 Handle Elesa+Ganter GN 428 Types Type A: Mounting from the back (threaded blind bore) Type B: Mounting from the operator's sideMaterial Aluminium AL plastic coated, black RAL 9005, textured finish SW anodized, natural colour ELIn type B lens screws, hexagon nuts and washers are included parts of the order. E+G M.543-p Handle Elesa+Ganter M.543-p HandleGlass-fibre reinforced polyamide based (PA) technopolymer, black or orange colour, matte finish. Zinc-plated steel threaded stud, chamfered flat end according to UNI 947 : ISO 4753 E+G ERB-PF Pull handle Elesa+Ganter ERB-PF Bi-directional flush pull handle snap-in assemblyGlass-fibre reinforced polyamide based (PA) technopolymer.Standard executions - ERB-PF: grey-black colour, matte finish. - ERB-PF-CLEAN: white colour similar to RAL 9002, matte finish. E+G MFH Finger handle Elesa+Ganter MFH Finger handlePolyamide based (PA) technopolymer. Resistant to solvents, oils, greases and other chemical agents.Blind holes for fitting by means of no. 2 self-tapping screws for plastic materials Ø3.5 (UNI ISO 7049). Screws are not included in the supply.Maximum tightening torque of the self-tapping screws 1,2 Nm.Standard executions: - MFH-AF: in 4 standard colours: black, orange, grey, red, matte finish. - MFH-AF-CLEAN: white colour similar to RAL 9002, matte finish. - MFH-CR: .... E+G GN 328.5 U-handle Elesa+Ganter GN 328.5 U-handleGN 328.5 Stainless Steel-Cabinet "U" handles have excellent stability and ergonomic design. The finger recesses on the underside of the handle provide a specially comfortable grip.Types:- Type A: Mounting from the back (threaded blind bore)- Type B: Mounting from the operator's sideMaterial:Stainless Steel-precision castingmatte shot-blasted GS E+G PR-PF Flush pull handle Elesa+Ganter PR-PF Flush pull handles for snap-in assemblyMaterial: Glass-fibre reinforced polyamide based (PA) technopolymer.Choose between the following clours - all with matte finish:Black (RAL 7021) C1Grey (RAL 7035) C3Orange (RAL 2004) C2Snap-in assembly (see Assembly Instructions in datasheet). E+G GN 428 U-handle E+G GN 435 U-handle Elesa+Ganter GN 435 u-handle in stainless steel, tall design.Stainless Steel-Cabinet U-handles GN 435, tall design, are made from bent round profiles and are designed for applications requiring more height for gripping. For example, this makes it possible to grab or hold the handle while wearing safety gloves. Some dimensions also satisfy the crane access standard DIN EN 13856. In addition to serving as a handle, it can also be used as a hose guide, retaining bracket or the like. Due to the manu .... E+G GN 435.3 U-handle Elesa+Ganter GN 435.3 U-handle in stainless steel, tall design - for welding.Stainless Steel-Cabinet U-handles GN 435.3, tall design, are made from bent round profiles and are fastened by welding. They are designed for applications requiring more height for gripping. For example, this makes it possible to grab or hold the handle while wearing safety gloves. Some dimensions also satisfy the crane access standard DIN EN 13856. The holes d2 serve, if necessary, for inserting dowel pins or guide pin .... E+G M.743 U-handle Elesa+Ganter M.743 U-handle with inclined shape.The inclined shape of the handle guarantees an ergonomic grip.Suitable for sliding door applications.Material:- High-resilience polypropylene based (PP) technopolymer handle, black colour, matte finish.Standard execution:- Brass bosses, threaded blind holes. E+G Tubular handle EVH Elesa+Ganter Turbular handle EVH combines ergonomics and design with functionality offering a safer and comfortable grip. The compact shapes, no cavities and protrusions, allow an excellent level of safety during operations of opening and closing of machines doors.The side caps with easy press-fit assembly in the seven Elecolors® allow the perfect match with the colours of the machines EVH are installed on.Material: - Glass-fibre reinforced polyamide based (PA) technopolymer.Types:- EVH-EP: .... E+G EVH-CLEAN E+G EVH-CLEAN Tubular handle is part of the Elesa ERGOSTYLE series of easy cleaning products. With oval cross section, technopolymer and aluminium.The large diameter of the tube offers a good and comfortable grip.Standard execution:Pass-through holes for cylindrical-head screws with hexagon socket, hexagonal-head screws or standard lock nuts.Aluminium tube, coating in white colour similar to RAL 9002, glossy finish.Suggested tightening torque:- back mounting with plain holes: 8 [Nm]- front mount .... E+G M.2000 Bridge handle E+G M.2000 Bridge handle in self-extinguishing technopolymerMaterialGlass-fibre reinforced polyamide based (PA) technopolymer certified self-extinguishing UL-94 V0, black colour, matte finish.Standard executionBrass bushings, M6 threaded blind holes for rear mounting.The M.2000 handle can be combined with M.2000-SWM handles with monostable electrical switch. E+G GN 328 U-handle E+G GN 328 U-handles in aluminium are made from die-cast aluminum and have excellent stability and ergonomic design. The finger recesses on the underside of the handle provide a comfortable grip.Types:- Type A: Mounting from the back (threaded blind bore)- Type B: Mounting from the operator's sideMaterial:- Aluminium AL, plastic coatedColours:- SW: Black RAL 9005 textured finish- SR: Silver RAL 9006 textured finish - BL: Blank, groundOther finishes on request E+G EVH. Tubular Handle Ergonomics, design and functionality integrated in a tubular handle that combines ergonomics and design with functionality offering a safer and comfortable grip.The anti-rotation oval cross section tube and compact shapes, no cavities, and protrusions, allow an excellent level of safety during operations of opening and closing of machines doors.Material:- Handle shanks: Glass-fibre reinforced polyamide based (PA) technopolymer, greyblack colour, matte finish- Covers type ECA.V: Polyamide based ( ....
